Lumastream Trinity Power Cord Manuel d'utilisateur télécharger pdf (Page 11)

Document: 66APPMAN-PC Rev: C 18 of 28

10.7 STANDALONE TEST MODES

 Test modes are specified by address location and may be used to

debug network connections or provide standalone color changing

options without the need for a DMX controller. Colours are assuming

LED loads are connected in RGB configuration as shown on page 15,

section 9.4)

ADDRESS FUNCTION/SEQUENCE

000 NO FUNCTION

001-512 DMX ADDRESS MODE

513 GREEN ON

514 RED ON

515 BLUE ON

516 BLUE & RED ON (MAGENTA)

517 BLUE & GREEN ON (CYAN)

518 GREEN & RED ON (YELLOW)

519 ALL OUTPUTS AT 5%

520 EACH COLOR RAMPING UP AND DOWN INDIVIDUALLY – SPEED 1

521 EACH COLOR RAMPING UP AND DOWN INDIVIDUALLY – SPEED 2

522 CROSS FADE BETWEEN COLOURS (RED UP, GREEN UP, RED

DOWN, BLUE UP ETC.) – SPEED 1

523 CROSS FADE BETWEEN COLOURS (RED UP, GREEN UP, RED

DOWN, BLUE UP ETC.) – SPEED 2

524 CROSS FADE BETWEEN COLOURS (RED UP, GREEN UP, RED

DOWN, BLUE UP ETC.) – SPEED 3

525 CROSS FADE BETWEEN COLOURS (RED UP, GREEN UP, RED

DOWN, BLUE UP ETC.) – SPEED 4

526 CROSS FADE BETWEEN COLOURS (RED UP, GREEN UP, RED

DOWN, BLUE UP ETC.) – SPEED 5

530 ALL ON

531 CHANNEL 1 ON

532 CHANNEL 2 ON

533 CHANNEL 3 ON

534 CHANNEL 4 ON

535 CHANNEL 5 ON

536 CHANNEL 6 ON

537 CHANNEL 7 ON

538 CHANNEL 8 ON

539 CHANNEL 9 ON

540 CHANNEL 10 ON

541 CHANNEL 11 ON

542 CHANNEL 12 ON

Document: 66APPMAN-PC Rev: C

11 of 28

8.0 OUTPUT CHANNEL REQUIREMENTS

8.1 Electrical Output Specifications:

Output specifications are defined in table 2 on page 4 of this manual.

Actual output currents and maximum voltages are dependant on the

model configuration, see table 6, 8 or table 10 at the beginning of this

manual for configuration options.

8.2 Output Wiring Requirements

 WARNING: All output channels are isolated from each other and

require a separate 2 wire twisted pair for each output LED load.

 When connecting LED loads to output cables observe ‘+’ and ‘-‘ po-

larity connections to prevent damage to loads. To reduce risk of fire or

electric shock, do not interconnect output terminations.

 A common anode or cathode wiring method for multiple LED

loads cannot be used for the TRINITY PC.

 All output wires should be connected to their respective LED loads

before power up to prevent inadvertent shorting of outputs. Shorting of

outputs (+ve to –ve only) will result in a hiccup mode of operation with

automatic recovery after removal of a short.

 Output Class 2 circuit wiring must comply with NEC Article 725 wir-

ing methods or to CEC section 16-210 wiring methods.

 Output cabling should be overall shielded cables with twisted pair

conductors (18 AWG ) to minimize cross talk between channels and mini-

mize Electromagnetic Interference (EMI).

 Consult your local Electrical Safety Authority for acceptability in

your end use application.

 With appropriate cabling, the TRINITY PC may be remote mounted

up to 150 feet (45 meters) from the LED loads.

7.0 INPUT REQUIREMENTS

7.1 Electrical Input Specifications:

Input specifications are defined in table 1 on page 4 of this

CAUTION

RISK OF DAMAGE:

 DO NOT connect input of power unit to a phase cut dimmer or dim-

ming panel. It will cause internal damage to the power unit

1 2 ... 6 7 8 9 10 11 12 13 14

Commentaires sur ces manuels

Pas de commentaire

Lumastream Trinity Power Cord Manuel d'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Lumastream Trinity Power Cord